If your looking to make some special marijuana treats, Cannabutter is a vital ingredient. The process of making cannabutter is basically just melting butter with marijuana, straining the marijuana and then re-solidifying the butter. This works because THC (the substance in marijuana that gets you “high”) sticks to the fat cells in butter. Cannabutter can be used in any recipe that calls for butter or oil.
In this thread I will attempt to teach those who don’t know how to make Cannabutter, how to do so. The pictures may help you but I highly recommend reading all the text word for word.
You will need the following:
1. A large saucepan.
2. A spoon for stirring.
3. Few Sticks of Butter (Its about 1lb. of butter to every ounce of weed so make sure you do the math correctly :).
4. Marijuana – If you are new to making Cannabutter I would recommend starting with a small amount.
5. Cheesecloth and some elastics.
6. A few tupperware containers with lids.
Bring a few cups of water to a boil on the stovetop, it doesn’t really matter how much water you use because in the end it will all be seperated, Just make sure the marijuana is always floating about 1 1/2 inches from the bottom of the pan.
When the water is at a boil place the butter in the pan, again it’s about 1lb. of butter, 4 sticks, to every ounce of marijuana, so if your using a half ounce of bud thats about 2 sticks of butter. Be sure not to let the butter burn, if it appears to be burning then let melt on a medium setting.
Move the dial to low heat once butter has melted, it should look like the picture below.
Now that the butter has melted you can now add the marijuana, Here I used about 5 grams of fresh nug and about 7 grams of vaped bud. Again make sure the stove is now on a low setting.
Stir occasionally, I tend to stir every time the mix starts bubbling. I usually let the bud simmer for 3 hours, but you can always tell it’s done when the top of the mix turns from a really watery consistency to glossy and thick.
While letting the mix simmer, You are now going to need to get the cheesecloth strainer ready, which will also be used to store the cannabutter.
Take two sheets of cheese cloth and fold each one over so they each have two layers, place these over a tupperware container (with the lid off), and secure them there with elastics.
It shoud look like the picture below. I say to make two just incase one container runs out of room.
When the water has turned glossy and thick on top it should look like the picture below.
You are now ready to strain the marijuana out of the mix, place your tupperware containers with the cheesecloth lids in the sink and slowly pour the entire mix on top of the cheesecloth like pictured below.
When the saucepan is empty carefully undo the elastic, pick up the cheesecloth from all four sides and squeeze all of the remaining butter out.
I throw away the marijuana after this, you can try and dry it out but I wouldn’t waste my time.
Now place the lid on the tupperware and place it in the fridge to sit overnight, You need to do this so the water can seperare from the cannabutter, be patient.
Now that you have awakened in anticipation for your new treat, its time to seperate the waste water!
It should look like the picture below. The cannabutter on top and the waste water on bottom.
Take the lid off the tuperware and hold it upside down over the sink, place a dish in the sink to catch any cannabutter that may fall, squeeze two sides of the tupperware and the waste water will pour out, once all the water is gone your done! The cannabutter is ready to cook with.
If you do not wish to cook with it now, you can just place it back in the tupperware, place the lid back on and store it in the fridge.
And be careful, the high from eating “special edibles” is often considered much more intense then inhaling, lasting anywhere from 2-8 hours. Do not attempt to eat too many at first. And I wouldn’t recommend driving. Just chill out, and enjoy!Thanks to “Hash” from 420Magazine forums for this awesome recipe!